|
|
|
|
|
|
|
|
|
|
|
|
|
|
This roller is a replacement for some Croft and Keller doors. It is also found in other household situations from the closet to the bathroom. It is a ball bearing 3/4 in high-density polyethylene roller on a threaded hex hub. Often fits onto a bracket that is attached to the door while the roller rides in an upper track above the door opening.
|
Plastic roller with narrow center groove 7/32 in W nylon wheel, concave edge. Includes a 8-32 x 3/8 in machine screw with binder post nut. Fits on air control doors.
|
3/4 in wide die-cast keeper, screw slots allow for vertical adjustment, universal application. Contains one keeper and installation fasteners.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Bent spring design used by Academy Mfg. And others. Center grooved 5/16 in W wheel, 2-1/4 in L x 5/16 in W flat high-tension heat treated steel spring and #8 x 3/8 in Phillips sheet metal screw.
|
Consists of 1/4 in W center groove wheel. Heat-treated, high-tension adjustable steel M-spring. Used by several patio door manufacturers.
|
Used by metal industries. Center grooved, 1/4 in W, roller. 1-3/4 in L, high-tension, heat treated steel spring. Includes #8 x 3/8 in Phillips sheet metal screw.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Used by metal industries. Center grooved, 1/4 in W, roller. 1-3/4 in L, high-tension, heat treated steel spring. Includes #8 x 3/8 in Phillips sheet metal screw.
|
Used by several patio door manufacturers. Consists of 1/4 in W center groove wheel, high-tension heat treated steel V-spring (2 in L before and 2 in L after bend).
|
Are you having trouble sliding your screen door open or closed. Have you checked your rollers/roller assemblies. Don't replace the entire door. For a fraction of the cost of a new door, replace those worn-out rollers. This sliding screen door roller assembly is made from a high-density polyethylene housing with a 1 in high-density polyethylene ball bearing roller. The roller arm is adjustable with the adjusting screw on-the end of the roller assembly. Most often found on Peachtree sliding screen doors, as well as a variety of other patio door manufacturers. Installation only requires the roller assembly to be inserted into the rectangle opening in the bottom of the door frame, then you slide it back until the installation holes align and install the screw. Order yours today and have your door slide like new.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For sliding glass doors. Center grooved, 5/16 in W steel ball bearing roller and steel inner race with 1/4-20 x 3/4 in carriage bolt and 1/4 in - 20 hex nut.
|
Used on Peachtree patio doors. Steel ball bearing roller, adjustable steel housing 2-1/4 in L x 1-9/16 in H x 17/8 in W. Contents: 1 roller assembly.
|
Used by Air Control, Howmet, Krestmark and many other patio door manufacturers. Steel ball bearing roller and adjustable 2-5/8 in L x 1-3/8 in H x 3/4 in D steel housing assembly with machine threaded holes (10-32 top and 1/4-20 side) for installation.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Used by Nu-Air and other glass door manufacturers. Steel housing dimensions: 3/4 in thickness, 1-3/16 in H and 2-1/8 in L. Overall thickness of roller assembly: 7/8 in. Concave roller edge type and plain back housing tab style.
|
Steel glass door roller. Housing width: 3/4 in. Roller edge type: Concave. Includes 1 roller assembly.
|
PL 15576 is a 96 in stainless steel track cap used to repair damaged patio or wardrobe door tracks. It can be cut to size. After the old track is prepared by grinding any spots that are wider than the original track width and cleaning it, the new track is simply pressed onto the old track after squirting a thin bead of silicone glue in the replacement track. Using a rubber mallet and a block of wood, the replacement track is snapped down over the old track.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Steel housing and hook, round end face plate. Hook position is adjustable, fits on W&F. Hole center of 3-11/16 in.
|
Easily restore smooth and reliable operation to your patio or sliding glass door with this Prime-Line D 1607 sliding door roller tandem assembly. Designed as a replacement for worn, damaged or missing rollers, this assembly helps extend the life of your door and improve its performance. It is commonly used by a variety of patio door manufacturers, making it a versatile repair solution for homeowners and DIY installers. The roller assembly features a durable stamped steel housing with a protective yellow zinc finish that resists wear and corrosion. Inside the housing are tandem concave steel ball bearing rollers, each measuring 1-1/4 in Dia x 5/16 in THK. These rollers are engineered to provide smooth gliding action, reduce door sticking and ensure long-lasting performance. The housing measures 11/16 in W, 1-3/16 in H and 4-5/8 in L, with a minimum collapsed height of 1-1/2 in. Installation and height adjustments can be made with a standard Phillips head screwdriver, making it a straightforward project for most DIY homeowners. Whether you are repairing a sliding patio door for the first-time or maintaining an older unit, this roller assembly is designed for strength, durability and ease of installation.
|
|
|
