Home > HARDWARE > CONSTRUCTION HARDWARE > JOIST HANGERS & CONNECTORS

Choose a sub category:

JOIST HANGERS	FRAMING ANGLES/ANCHORS	MENDING PLATES
NAIL PLATES	POST ANCHORS / CAPS	FENCE BRACKETS
INSULATION SUPPORTS	STRAPS	PLYWOOD CLIPS
FOUNDATION ANCHORS	BRICK/WALL TIES	MISC CONSTR HARDWARE

Wood Construction Connectors

Sort By:


Acorn International IHW16100 Insulation Support Wire, 16 in OAL, Carbon Steel, 100/CT Our Price: $15.04	Acorn International IHW24100 Insulation Support Wire, 24 in OAL, Carbon Steel Our Price: $22.51	Tamlyn PCS Series PCSL716 Framing Plywood Clip, 20 ga Thick Material, Steel, Galvanized Our Price: $24.62

Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2 in less than over center joist spacing. 13 ga.	Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2 in less than over center joist spacing. 13 ga.	Tamlyn PCS Framing Plywood Clip, Steel, Galvanized, Material Thickness: 20 ga, Maximum Roof Span: 24 in, Number of PC per Spans: 1


Tamlyn PCS12 Framing Plywood Clip, 32 with PC, 28 without PC Roof Span, 20 Thick Material, Steel Our Price: $24.62	Tamlyn PCSL1532 Framing Plywood Clip, 20 ga Thick Material, Steel, Galvanized Our Price: $24.62	Tamlyn PCS58 Framing Plywood Clip, 40 with PC, 32 without PC Roof Span, 20 Thick Material, Steel, Galvanized Our Price: $30.68

Replace wood blocking on roof sheathing. Tight fit for positive installation. Embossed dimples provide 1/8 in gap needed to prevent panels from popping up as sheathing expands. G60 galvanizing finish. 20 ga, Boxed.	Tamlyn Framing Plywood Clip, Steel, Galvanized, Material Thickness: 20 ga, Maximum Roof Span: 32 in, Number of PC per Spans: 1	Replace wood blocking on roof sheathing. Tight fit for positive installation. Embossed dimples provide 1/8 in gap needed to prevent panels from popping up as sheathing expands. G60 galvanizing finish. 20 ga, Boxed.


2x4basics 90166 Bracket, Resin, Sand Our Price: $38.49	Tamlyn PC1532 Plywood Clip, 32 with PC, 28 without PC Roof Span, Aluminum, Mill Our Price: $40.70	Acorn International IHW16500 Insulation Support Wire, 16 in OAL, Carbon Steel, 500/CT Our Price: $49.95

You determine the size. Connect with railing brackets with 2x4 and 2x6 lumber to easily add a bench to any size or shape deck. Gain increased seating area while using only 7 in of deck space. Assembled unit stands 36 in H for deck railing, seat is 17 in H. Quick and easy to assemble using basic tools. Includes bench bracket, hardware and instructions. Lumber not included.	With built-in spacer for use when support spacing exceeds the maximum length of an unsupported edge. Boxed.	Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2 in less than over center joist spacing. 13 ga.


Tamlyn BT22ZZSP Storage Strap, 6-3/8 in L, 7/8 in W, Galvanized Steel Our Price: $60.30	Grabber Construction Deckmaster Series DMP100-10 Hidden Bracket, For: 3/4 in Decking Powder Coat Brackets Our Price: $82.30	Acorn International WT-ST Wall Tie, 6-3/8 in L, 7/8 in W, Carbon Steel Our Price: $83.11

Masonry accessory used to tie a brick veneer to the exterior of the house. Two holes provide for nailing on one end, other end is bent to lie between the mortar joints. Follow local codes for spacing. 6-3/8 in x 7/8 in.	When using the Grabber Deckmaster fastening system, all fasteners are hidden beneath the deckboards. There is no surface penetration of the deckboards or joists. With Grabber Deckmaster there are no exposed screws a primary entry point for moisture and deck board damage. No stains or splinters form around fastener holes.	Acorn International Wall Tie, Carbon Steel, 6-3/8 in Length, 7/8 in Width, 22 ga


Acorn International IHW24500 Insulation Support Wire, 24 in OAL, Carbon Steel, 500/CT Our Price: $84.63	Grabber Construction Deckmaster Series DMP125-10 Hidden Bracket, 22-1/2 in L Dimensions, Powder-Coated Our Price: $85.24	Grabber Construction Deckmaster Series DMP100-100 Hidden Bracket, For: 3/4 in Decking Grabbergard Brackets Our Price: $620.02

Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2 in less than over center joist spacing. 13 ga.	When using the Grabber Deckmaster fastening system, all fasteners are hidden beneath the deckboards. There is no surface penetration of the deckboards or joists. With Grabber Deckmaster there are no exposed screws a primary entry point for moisture and deck board damage. No stains or splinters form around fastener holes.	When using the Grabber Deckmaster fastening system, all fasteners are hidden beneath the deckboards. There is no surface penetration of the deckboards or joists. With Grabber Deckmaster there are no exposed screws a primary entry point for moisture and deck board damage. No stains or splinters form around fastener holes.


Grabber Construction Deckmaster Series DMP125-100 Hidden Bracket, For: 5/4 in Decking Grabbergard Brackets Our Price: $620.02	Grabber Construction Deckmaster Series DMP175-100 Hidden Bracket, Powder-Coated, For: 2x Decking Grabbergard Brackets Our Price: $626.53

When using the Grabber Deckmaster fastening system, all fasteners are hidden beneath the deckboards. There is no surface penetration of the deckboards or joists. With Grabber Deckmaster there are no exposed screws a primary entry point for moisture and deck board damage. No stains or splinters form around fastener holes.	When using the Deckmaster fastening system, all fasteners are hidden beneath the deckboards. There is no surface penetration of the deckboards or joists. With Deckmaster there are no exposed screws a primary entry point for moisture and deck board damage. No stains or splinters form around fastener holes.


	1

A construction project is only as strong as its weakest joint, which is why we carry a full line of wood construction connectors or metal ties for wood for any type of building project. Build a house, deck or even a flip-top bench table or workbench with a convenient kit. Our metal connectors for wood framing are made from heavy-gauge steel, galvanized or zinc-finish metal.

Scroll through our extensive online collection of wood beam connectors, joist hangers, straps, plates, brick wall ties and more, or head out to our Smyrna, GA, and Norcross, GA, shops to buy in person. We offer wood framing connectors in a wide range of sizes from multiple well-known manufacturers. Contractors and do-it-yourself enthusiasts alike will appreciate the convenient deck bracket kits, building kits and anti-floor-squeak sets, too.