Home > ELECTRICAL > ROUGH ELECTRICAL > SURFACE WIRING
Choose a sub category:
WALL CHANNEL- WIREMOLD
Sort By:
1 2
CordMate Legrand C19 Channel Coupling CordMate Legrand C Wireway Outside Elbow CordMate Legrand C Wireway Inside Elbow
Hides and organizes loose cords and wire. Hides and organizes loose cords and wire. Hides and organizes loose cords and wire.
CordMate Legrand C Wireway Flat Elbow CordMate II Legrand C Wireway Flat Elbow CordMate II Legrand C59 Joint Cover Channel Coupling
Hides and organizes loose cords and wire. Hides and organizes loose cords and wire. Hides and organizes loose cords and wire.
CordMate II Legrand C 3-Way Standard T-Fitting CordMate II Legrand C Wireway Inside Elbow CordMate II Legrand C Wireway Outside Elbow
For installation requiring 3-way branching including 90-deg angle. For making a 90 deg turn around an inside corner from wall-to-wall or wall-to-ceiling. For making a 90 deg turn around an outside corner.
Legrand NM8 Nonmetallic Raceway Outside Elbow Legrand NM7 Nonmetallic Raceway Inside Elbow Legrand NM11 T-Fitting
For making a 90 deg outside turn around a corner. For making a 90 deg inside turn around a corner from wall-to-wall or wall-to-ceiling. For branching wire channel in two directions at 90 deg angles.
Legrand NMW910 Raceway Accessory Pack Legrand NM6 Nonmetallic Raceway Flat Elbow CordMate Legrand NM Raceway Wireway Inside Elbow
Mounting components for NM1 wire channel, including screws and anchors, wire clips and joint cover. For making 90 deg right or left turns on a flat surface. For making a 90 deg inside turn around a corner from wall-to-wall or wall-to-ceiling.
CordMate Legrand NM Raceway Wireway Outside Elbow Wiremold NM910 Connection Cover Legrand B-7 Metal Raceway Inside Elbow
For making a 90 deg outside turn around a corner. Mounting components for NM1 wire channel, including screws and anchors, wire clips and joint cover. Used to make a 90 deg inside turn around a corner, from wall-to-wall or wall-to-ceiling.
CordMate Legrand NMW11 3-Way T-Fitting Legrand B-6 Metal Raceway Flat Elbow CordMate Legrand NM Raceway Wireway Flat Elbow
For branching wire channel in two directions at 90 deg angles. Used to make a 90 deg right or left turn on a flat surface. For making 90 deg right or left turns on a flat surface.
Legrand NMW17 Raceway Conduit Connector Legrand B-8 Metal Raceway Outside Elbow CHANNEL WIRE PLASTIC 5FT WHITE
For transitioning from non-metallic raceway to conduit. Hides and organizes loose cords and wires. Used to make a 90 deg outside turn around a corner. Hides and organizes low voltage loose cords and wires. UL Listed. 1/2" height x 3/8" width x 5' length.
Wiremold NMW2 Starter Box Wiremold Raceway On-Wall Mount Conduit Connector Wiremold NMW3 Outlet Box
Fits over existing single gang outlet to feed power as the starting point for your system. 1 in D. For transitioning from non-metallic raceway to conduit. Hides and organizes loose cords and wires. For installing dimmer switches as well as standard size switches and outlets. 1-7/16 in L x 1-3/8 in D.
Legrand NM Outlet Box Legrand NM Deep Outlet Box Legrand NM Extra Deep Outlet Box
Fits over existing single gang outlet to feed power as the starting point for your system. 1 in D. For installing dimmer switches as well as standard size switches and outlets. 1-7/16 in L x 1-3/8 in D. For installing speed controls for ceiling fans dimmer switches, standard switches and outlets. 1-3/4 in D.
   
 
1 2